Coolquest, Inc.	Home	Products	Support	About	Contact
C++BOLD Example Parts Library

$INSERT
// THIS FILE IS IN THE PUBLIC DOMAIN.
// IT IS PROVIDED AS IS WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING, BUT
// NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
 
$END
 
//Voltage Regulator part file
 
$PART_NAME ADR318ARJ    // Analog devices 1.8 V, 5 mA reference
$JEDEC_TYPE SOT23
$REF_PREFIX U
$PIN_COUNT 5
$PORTS
    SHDN_N      1;
    VIN         2;
    VOUT_SENSE  3;
    VOUT_FORCE  4;
    GND         5;
$ENDPORTS
$ENDPART
 
 
$PART_NAME LT1963AEST   // Linear Technology low noise, low-dropout voltage regulator in SOT-223
$JEDEC_TYPE SOT223
$REF_PREFIX U
$PIN_COUNT 4            // 3 pins plus tab
$PORTS
    IN         1;
    OUT        3;
    GND[2]     2 TAB;
$ENDPORTS
$ENDPART
 
 
$PART_NAME LT1963AES8   // Linear Technology low noise, low-dropout voltage regulator in SOIC8
$JEDEC_TYPE SOIC8
$REF_PREFIX U
$PIN_COUNT 8
$PORTS
    IN         8;
    OUT        1;
    SENSE_ADJ  2;       // SENSE for fixed-voltage parts, ADJ for adjustable parts
    GND[3]     3 6 7;
    SHDN_N     5;
    NC         4;
$ENDPORTS
$ENDPART
 
 
$PART_NAME TL751L   // TI low-dropout voltage regulator
$JEDEC_TYPE SOIC8
$REF_PREFIX U
$PIN_COUNT 8
$PORTS
    INPUT    8;
    OUTPUT   1;
    GND[4]   2 3 6 7;   // "COMMON" on data sheet
    ENABLE_N 5;         // for TL750L, pin five is NC
    NC       4;
$ENDPORTS
$ENDPART
 
 
$PART_NAME REG103UA   // TI low-dropout voltage regulator in D package (SOIC)
$JEDEC_TYPE SOIC8
$REF_PREFIX U
$PIN_COUNT 8
$PORTS
    INPUT[2]    8 7;  // "VIN" on data sheet
    OUTPUT[2]   1 2;  // "VOUT" on data sheet
    GND           4;  // "COMMON" on data sheet
    NR            3;  // Noise reduction (Adjust on REG103A-A)
    ENABLE        5;  // tie to INPUT
    ERROR_N       6;  // open-drain output
$ENDPORTS
$ENDPART
 
 
$PART_NAME PT7711C
$JEDEC_TYPE PTSMT1430C        // surface-mount package
$REF_PREFIX U
$PIN_COUNT 33
$PORTS
    VID[4:0] 6 4 3 2 1;
    STBY_N 5;
    VIN[5] 7 8 9 10 11;
    RS_GND 12;
    GND[13] 13 14 15 16 17 18 19 M1 M2 M3 M4 M5 M6;    // M1-M6 are mechanical pins
    VOUT[6] 20 21 22 23 24 25;
    RS_VOUT 26;
    SYNC_OUT 27;
$ENDPORTS
$ENDPART
 
 
$PART_NAME PT6701C
$JEDEC_TYPE PTSMT1310C       // surface-mount package
$REF_PREFIX U
$PIN_COUNT 29
$PORTS
    OVP_DRIVE 1;
    PWR_GOOD 2;
    VID[4:0] 7 6 5 4 3;
    STBY_N 8;
    NC     9;              // do not connect
    VIN[3] 10 11 12;
    RS_GND 13;
    GND[11] 14 15 16 17 18 M1 M2 M3 M4 M5 M6;    // M1-M6 are mechanical pins
    VOUT[4] 19 20 21 22;
    RS_VOUT 23;
$ENDPORTS
$ENDPART
    
// parts above are preferred to those below
// !! double-check parts below for mechanical pins
 
$PART_NAME PT6603C
$JEDEC_TYPE PTSMT400
$REF_PREFIX U
$PIN_COUNT 14
$PORTS
    RS 1;
    NC 2;
    STBY_N 3;
    VIN[3] 4 5 6;
    GND[4] 7 8 9 10;
    VOUT[3] 11 12 13;
    VOUT_ADJ 14;
$ENDPORTS
$ENDPART
 
 
$PART_NAME PT7707C
$JEDEC_TYPE PTSMT810
$REF_PREFIX U
$PIN_COUNT 27
$PORTS
    VID[4:0] 6 4 3 2 1;
    STBY_N 5;
    VIN[5] 7 8 9 10 11;
    RS_GND 12;
    GND[7] 13 14 15 16 17 18 19;
    VOUT[6] 20 21 22 23 24 25;
    RS_VOUT 26;
    SYNC_OUT 27;
$ENDPORTS
$ENDPART
 
 
$PART_NAME PTH05000WAS
$JEDEC_TYPE PTSMT_EUT        // surface-mount package
$REF_PREFIX U
$PIN_COUNT 5
$PORTS
    VOUT       5;
    VO_ADJUST  4;
    INHIBIT_N  3;
    VIN        2;
    GND        1;
$ENDPORTS
$ENDPART